RF Output Channel
If you need additional operating assistance after
reading this owner’s manual or to order replace-
ment accessories, please call
If channel 3 is already occupied for broadcasting,
1) Set your TV to channel 4.
2) Insert a pre-recorded tape into the VCR.
3) Press the PLAY button once.
Hint
Owner’s Manual
• The RF output channel may
not change when you adjust
tracking during playback. In
this case, stop the playback,
and start the playback again.
After that, press the PLAY but-
ton on the VCR for 3 seconds
again.
TOLL FREE : 1-800-968-3429
Video Cassette Recorder
4) After a few seconds, press the PLAY button on the VCR for 3 seconds.
6240VE
•
The RF output channel will change to channel 4 from channel 3 and you will
see a playback picture.
•
When a picture does not appear on the TV screen, repeat step [4].
5) Press the STOP button to stop playback.
1. Before using your VCR
StereoTV Connection
BasicVCR/TV Connection
VIDEO
IN
AUDIO IN
You can use the AUDIO OUT jack and
VIDEO OUT jack on the back of the
VCR if your TV has Audio/Video Input
jacks. In this case, you need to set the
TV to external Line Input Mode. Please
refer to your TV’s owner’s manual.
L
R
ANT
IN
Antenna
Antenna
Cable
Signal
or
Cable
Signal
or
(Back of VCR)
AUDIO
OUT
IN
OUT
(Back of TV)
VIDEO
(Back of TV)
ANT
IN
Audio/Video Cables
(not supplied)
ANT
IN
OUT
2
VIDEO
OUT
AUDIO OUT
1
L
R
Disconnect
3
OUT
Connect
Connect
(Back of VCR)
(Back of TV)
Connect
RF Cable (supplied)
Front & RearTerminals
AUDIO OUT jack
AUDIO IN jack
Plug the AC power cords of the VCR and TV into the AC outlets.
Connect the audio cable to the audio in jack
of a camcorder, another VCR, a stereo
amplifier, or an audio system.
4
Connect the audio cable from the audio out
jack of a camcorder, another VCR, or an
audio source.
Hint for Cable Box or Satellite Box
(Back of VCR)
ANT
(Back of VCR)
Connection B
Connection A
ANT IN jack
Connect your antenna or cable box.
IN
(Cable box or
Satellite box)
ANT
IN
ANT
IN
(Cable box or
Satellite box)
ANT
IN
AUDIO
IN
OUT
OUT
Cable
Signal
E
AUDIO
E
OUT
IN
OUT
RF Cable
(supplied)
OUT
IN
Cable
Signal
OUT
ANT OUT jack
OUT
IN
VIDEO
OUT
(Back of TV)
(Back of TV)
Connect the RF cable (supplied) to
RF Cable (supplied)
RF Cable
VIDEO
the antenna input jack on your TV.
Select this connection when you want to view or record a Select this connection when you want to change channels
VIDEO OUT jack
scrambled channel. With this connection, channels cannot
be changed on the VCR.You can view or record ONLY the
channels you have selected on the cable box or the satellite
box.
on the VCR. With this connection, you may watch one
channel while recording another.
Connect the video cable to the video in jack
of a camcorder, another VCR, or a TV.
VIDEO IN jack
Connect the video cable from the video out
jack of a camcorder, another VCR, or an
audio-visual source (laser disc player,
video disc player, etc.).
• You may not view or record a scrambled channel.
POWER
CHANNEL
M
• While you are recording, only the recorded channel can
be viewed.
T
o select channels of the cable box or satellite box
VIDEO
AUDIO
TAPE IN
1)At the cable box or satellite box, select channel 3 or 4
(the same channel as the VCR’s RF output channel.)
• Refer to “RF Output Channel”.
T
o select channels of the cable box or satellite box
1)Turn on the VCR by pressing the POWER button, and
then, press the VCR/TV button.The POWER and the
VCR/TV indicators on the front panel will light on. Then,
press the CHANNEL buttons to select channel 3 or 4
(the same channel as the output channel of the cable
box or satellite box).
2)At the TV, select the same channel as the output chan-
nel (3 or 4) of the cable box or satellite box.
Installing the Batteries for
the Remote Control
Install two AA batteries
(supplied) matching the
polarity indicated on
the bottom of the
Supplied Accessory
3)Turn on the VCR by pressing the POWER button, and
then, press the VCR/TV button .The POWER and
VCR/TV indicators on the front panel will light on. Then,
select the channel you want to view or record.
• Remote control
(NA371UD) with
Two AA batteries
• RF Cable
• Owner’s Manual
(WPZ0901TM002) (0VMN03900)
• If you use the channel 4, you need to change the VCR’s
RF output to channel 4. Refer to “RF Output Channel”.
2) At the TV, select channel 3 or 4 (the same channel as
you have selected at step 1).
3) At the cable box or satellite box, select the channel you
want to view or record.
T
o play back a tape
Follow the steps 1) to 2) above. Then, play back a tape.
• Refer to “Playback” on page 5.
remote control.
To view one channel while recording another
1)While you are recording on the VCR, press the VCR/TV but-
ton so that the VCR/TV indicator disappears on the VCR.
2)At the cable box or satellite box, select the channel you
want to view.
Printed in China
0VMN03900 / HF310UD ★★★★★
- 1 -
3. Preset for Use
Turn on theVCR for the first time
To Add/Delete Channels
Clock Set Up
MENU
MENU
To Select a Channel
-MENU-
-MENU-
1
1
1
5
6
7
CLOCK SET
MONTH DAY YEAR
You can select a channel by directly
pressing the Number buttons on the
remote control.
Notes for using the Number but-
tons:
TIMER PROGRAMMING
AUTO REPEAT [OFF]
B CHANNEL SET UP
CLOCK SET
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
Turn on the TV and set
it to channel 3.
0 3 1 5 MON 2 0 0 4
/
HOUR MINUTE AM/PM
0 5 – – – –
LANGUAGE SELECT
or
or
or
• If channel 3 is already occupied for broad-
casting, see“RF Output Channel” section.
:
or
•
When selecting cable channels which
are higher than 99, enter channel
numbers as a three-digit number.(For
example: 117, press 1,1,7)
Select the current hour
or
• If the clock is not set, the
CLOCK SET screen
appears when you press
the MENU button. In this
case, go to step [2].
POWER
Remote Control TV Screen
LANGUAGE SELECT
2
3
• You must precede single-digit
channel numbers with a zero (For
example: 02, 03, 04 and so on).
CLOCK SET
B ENGLISH
FRANCAIS
ESPAÑOL
[ON]
MONTH DAY
YEAR
0 3 1 5 MON 2 0 0 4
/
2
3
CHANNEL SET UP
2
3
4
CLOCK SET
HOUR MINUTE AM/PM
0 5 4 0 – –
To Preset the Channel Again
1) Press the MENU button until the main
:
or
AUTO SET UP
MONTH DAY
0 3 – –
YEAR
B MANUAL SET UP
/
– – – –
or
menu appears.
HOUR MINUTE AM/PM
– – – – – –
or
Select the current minute
CLOCK SET
:
2) Select "CHANNEL SET UP" by pressing the
PLAY or STOP button. Then, press the
F.FWD button.
Select the current month
CH 01
3) Select "AUTO SET UP" by pressing the
PLAY or STOP button. Then, press the
F.FWD button. After scanning, the tuner
stops on the lowest memorized channel.
MONTH DAY
YEAR
AUTO SET UP
0 3 1 5 MON 2 0 0 4
/
MANUAL SET UP
CLOCK SET
HOUR MINUTE AM/PM
CHANNEL 30
ADD
(CATV)
0 5
:
4 0
P M AM
B PM
MONTH DAY
0 3 1 5
YEAR
– – – –
To Change the On-Screen Language
1) Press the MENU button until the main
/
or
Do you connect the cable of the cable box or
the satellite box to the VCR’s ANT IN jack?
HOUR MINUTE AM/PM
– – – – – –
or
Select “AM” or “PM”
menu appears.
:
Yes
2) Select "LANGUAGE SELECT" by pressing
the PLAY or STOP button. Then, press the
F.FWD button.
Select the channel to be
added or deleted.
Select the current day
Yes Press the MENU
button to exit
3) Select "ENGLISH" , "FRANCAIS" or
"ESPAÑOL" by pressing the PLAY or STOP
button. Then, press the C.RESET/EXIT but-
ton.
• Refer to “Hint for Cable Box or
8
To exit the CLOCK SET
screen.
Satellite Box” section on page 1.
No
4
5
MANUAL SET UP
CLOCK SET
No Please wait for a few minutes.
CHANNEL 30
ADD
(CATV)
MONTH DAY
0 3 1 5
YEAR
2 0 0 4
or
After scanning...
/
• The tuner stops on the lowest memorized
channel.
or
HOUR MINUTE AM/PM
– – – – – –
:
• You can select only the channels memorized
Hint
in VCR by using the CHANNEL buttons.
• If "AUTO SET UP" appears on the TV screen
again, check the cable connections. Then,
press the F.FWD button once again.
Select “ADD” or “DELETE”
• To go back one step, press the REW button
(during the steps [2] to [7].)
Hint
Select the current year
• If you accidentally select Spanish or French
and need English: Press the MENU button
and choose SELEC. IDIOMA, or SELEC-
TION LANGUE. Press the F.FWD button,
and select ENGLISH. Finally, press the
C.RESET/EXIT button.
• Your clock setting will be lost if there is a
power failure or if the VCR has been
unplugged for more than 30 seconds.
Hint
C.RESET
EXIT
To exit the
menu.
•
Repeat these steps only if there was a
power failure or if the VCR has been
unplugged for more than 30 seconds.
- 3 -
EN
4. Precautions
Troubleshooting Guide
Precautions
Install Location
For safety and optimum performance of
your VCR:
Important Copyright Information
If you are having problems operating your product even though you have followed
the instructions in this manual, check the following list of problems and corrective
actions. You may be able to solve the problem yourself.
Unauthorized recording or use of broad-
cast television programming, video tape,
film or other copyrighted material may
violate applicable copyright laws. We
assume no responsibility for the unau-
thorized duplication, use, or other acts
which infringe upon the rights of copy-
right owners.
• Install the VCR in a horizontal and sta-
ble position. Do not place anything
directly on top of the VCR. Do not
place the VCR directly on top of the TV.
• Shield it from direct sunlight and keep it
away from sources of intense heat.
Avoid dusty or humid places. Avoid
places with insufficient ventilation for
proper heat dissipation. Do not block
the ventilation holes on the sides of the
VCR. Avoid locations subject to strong
vibration or strong magnetic fields.
PROBLEM
CORRECTIVE ACTION
No power.
• Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
Timer recording is impossible.
• Make sure the timer recording is set correctly.
• Make sure the power is off.
• Make sure the VCR clock is set correctly.
Cannot go into Recording mode. • Make sure the tape has a record tab. If needed, cover the hole with
cellophane tape.
A Note about Recycling
This product's packaging materials are
recyclable and can be reused. Please
dispose of any materials in accordance
with your local recycling regulations.
Batteries should never be thrown away
or incinerated but disposed of in accor-
dance with your local regulations con-
cerning chemical wastes.
Playback picture is partially noisy. • Adjust tracking control for a better picture by pressing the CHANNEL
buttons.
No playback picture (only sound
can be heard.)
•
Head cleaning may be necessary. Refer to “Auto Head Cleaning” on
page 8.
• Make sure the VCR is not in the Menu mode.
Avoid the Hazards of Electrical Shock and
Fire
• Do not handle the power cord with wet
hands.
• Do not pull on the power cord when
disconnecting it from AC wall outlet.
Grasp it by the plug.
No or poor playback picture.
• Turn on the TV and set the TV to channel 3. If channel 3 is already
occupied for broadcasting, change the RF output to channel 4, and
change the TV channel to channel 4. (See “RF Output Channel” on
page 1 for the detail.)
• Fine tune the channel reception on your TV.
Note to the Cable TV System Installer
TV programs cannot be seen nor- • Re-check the ANT. IN and ANT. OUT connections. See page 1.
This reminder is provided to call the
Cable TV system installer’s attention to
Article 820-40 of the National Electrical
Code, which provides guidelines for
proper grounding – in particular, specify-
ing that the cable ground shall be con-
nected to the grounding system of the
building, as close to the point of cable
entry as possible.
mally.
• Press the VCR/TV button on the remote control so that the VCR/TV
indicator on the VCR disappears.
No VCR operation from the
infrared Remote Control.
• Make sure the power plug is connected to an AC outlet.
• Check batteries in remote control.
Moisture Condensation Warning
Moisture condensation may occur inside
the unit when it is moved from a cold
place to a warm place, or after heating a
cold room or under conditions of high
humidity. Do not use the VCR at least for
2 hours until its inside is dry.
Video or color fades in and out when • You cannot copy a copyrighted video tape. You are experiencing copy
making a copy of a video tape.
guard protection.
Specifications
CAUTION:
Video Heads :
Operating temperature : 41°F~104°F
(5°C~40°C)
Four Heads
Power requirement : 120V, 60Hz
Power consumption : 14 Watts
FCC Warning
TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
ATTENTION:
This equipment may generate or use
radio frequency energy. Changes or
modifications to this equipment may
cause harmful interference unless the
modifications are expressly approved in
the instruction manual. The user could
lose the authority to operate this equip-
ment if an unauthorized change or modi-
fication is made.
Dimensions :
W 14-3/16” (360mm)
Converter output :
VHF Channel 3 or 4.
H 3-5/8” (92mm)
D 8-9/16” (216mm)
4.0 lbs. (1.8 Kg.)
(approx.)
POUR ÉVITER LES CHOC
ÉLECTRIQUES, INTRODUIRE LA
LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRE-
SPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
Weight :
• Designs and specifications are subject to change without notice and legal obligation.
• If an explanation in the Owner’s Manual is not consistent across languages, please
refer to the English version.
- 4 -
EN
5. Playback
7. Other Operations
Before:
To cue or review picture during play- To play back in slow motion
1
Turn on the TV and set it to
channel 3.
• If channel 3 is already occupied for broad-
casting, see “RF Output Channel” section.
back (Picture Search)
Press the SLOW button during playback
or the still mode.
• If the noise bar appears on the TV
screen, you can reduce it by pressing
the CHANNEL buttons.
POWER
EJECT
1
VCR/TV
3
Press the F.FWD or REW button.
• Press it again and the VCR will now
search in super high speed. (in the
LP/SLP modes only)
4
3
2
5
8
0
CHANNEL
4
6
SEARCH
-MODE
Remote Control TV Screen
7
9
2
4
1
3
CHANNEL
MENU REC/OTR STOP/EJECT
REW
PLAY
F.FWD
To freeze the picture on TV screen
To temporarily stop recording
C.RESET
EXIT
TAPE IN
MENU
SLOW
during playback (Still mode)
(Pause mode)
PLAYB
PAUSE
/STILL
REC/OTR SPEED
DISPLAY
Press the PAUSE/STILL button. Each
Press the PAUSE/STILL button.
TAPE IN
time you press the button, the picture will • During the rec pause mode, five
C
3 2
4
be forwarded by one frame.
marks appear on the TV screen. Each
C
2
• If the picture begins to vibrate vertically
during the still mode, stabilize the pic-
ture by pressing the CHANNEL buttons.
• If the picture is distorted or rolling verti-
cally, adjust the vertical hold control on
your TV, if equipped.
mark represents one minute.
• Press it again to resume recording.
Hint
EJECT
STOP
EJECT A
Auto Rewind
•
When a tape without record tab is inserted, the VCR will start playback auto-
matically at step [1].
• Tracking will be automatically adjusted upon playback. To adjust the tracking manu-
When a tape reaches its end during play-
back, fast-forward, or recording (except
timer recording and One Touch
Recording), the tape will automatically
rewind to the beginning. After rewinding
finishes, the VCR will eject the tape and
turn itself to off.
ally, press the CHANNEL buttons.
Counter Reset
Press the C.RESET/EXIT button.
6. Recording & OTR (One Touch Recording)
Before:
Hint
• Still/Slow/Pause mode will be automatically cancelled after 5 minutes to prevent damage to the tape and the
video head.
2
Turn on the TV and set it to
channel 3.
• To return to playback from the Picture Search/Still/Slow mode, press the PLAY button.
•If channel 3 is already occupied for
1
4
2
6
broadcasting, see “RF Output Channel” section.
POWER
EJECT
1
VCR/TV
3
8. On-Screen Operations
Remote Control TV Screen
1
2
1
4
7
2
5
8
0
with tab
CHANNEL
4
6
2
5
8
0
3
6
9
1
2
3
4
To call up the main menu
CHANNEL
SEARCH
-MODE
7
9
CH12
-MENU-
MENU
CHANNEL
MENU REC/OTR STOP/EJECT
REW
PLAY
F.FWD
C.RESET
EXIT
TAPE IN
MENU
SLOW
TAPE IN
B TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
• Select the
desired channel
PAUSE
/STILL
REC/OTR SPEED
DISPLAY
4
3
5
CHANNEL
MENU REC/OTR STOP/EJECT
REW
PLAY
F.FWD
LANGUAGE SELECT
TAPE IN
5
6
• Select the desired tape
speed
3
SP
SPEED
To select an item
Tape Speed
Recording/Playback Time
Type of tape
SP mode
SLP mode
T60
T120
2hours
6hour
T160
2-2/3hours
8hour
-MENU-
1
4
2 3
1hour
3hour
or
TIMER PROGRAMMING
AUTO REPEAT [OFF]
B CHANNEL SET UP
CLOCK SET
Accidental erasure prevention
REC/OTR
4
LANGUAGE SELECT
To prevent accidental recording on a record-
ed cassette, remove its record tab. To record
on it later, cover the hole with cellophane
tape.
REC
POWER
To decide
EJECT
VCR/TV
You can select a fixed recording time by press-
ing the REC/OTR button repeatedly.
1
4
2
5
8
0
3
6
Record tab
CHANNEL SET UP
CHANNEL
REC
OTR(0:30)
OTR(1:00).....
(Normal recording)
AUTO SET UP
SEARCH
-MODE
7
9
B MANUAL SET UP
OTR(8:00)
OTR(7:30)
C.RESET
EXIT
MENU
SLOW
4
3
4 1
2
PAUSE
/STILL
EJECT
5
6
REC/OTR SPEED
DISPLAY
Hint
STOP
EJECT A
To exit the menu
C.RESET
EXIT
MENU
• If you have connected the VCR to a cable box or satellite box, refer to “Hint for
Cable Box or Satellite Box” section on page 1.
OR
- 5 -
EN
9. Recording Features
Timer Recording
Hint forTimer Recording
•Insert a tape with its record tab into the VCR.
• If there is a power failure or the VCR has been unplugged for more than 30 sec-
onds, the clock setting and all timer settings will be lost.
• If the tape runs out before the end time, the VCR will switch to the Stop mode
immediately, eject the tape and the VCR power will be turned off. The TIMER
indicator will flash.
• If a tape is not in the VCR or does not have the record tab, the TIMER indicator
flashes and timer recording cannot be performed. Please insert a recordable tape.
• When all the Timer Recording are completed, the TIMER indicator flashes.
To play or eject the recorded tape, press the POWER button first, and then
press the PLAY or EJECT button.
-MENU-
1
ONE TIME PROGRAM
PROGRAM NUMBER
5
Select the desired start
time (hour)
9
4
B TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
DATE
0 5 / 0 3 MON
MENU
START TIME 0 7 : 3 0 PM
END TIME 0 8 : 3 0 PM
ONE TIME PROGRAM
or
LANGUAGE SELECT
PROGRAM NUMBER
DATE 0 5 / 0 3 MON
START TIME 0 7 : 3 0 – –
END TIME – – : – – – –
4
or
CHANNEL
1 6
REC SPEED SP
B SP
SLP
CHANNEL
– –
Select the desired recording speed
REC SPEED – –
C.RESET
EXIT
Select the
minute
To cancel a Timer Recording that is in progress
Press the STOP/EJECT button on the VCR.
2
PROGRAM NUMBER
DATE – – / – –
4
POWER
or
10 Turn off the VCR
for recording
START TIME – – : – – – –
END TIME – – : – – – –
Copying aVideoTape
CHANNEL
REC SPEED – –
– –
or
Warning: Unauthorized recordings of copyrighted video tapes
• TIMER indicator on the VCR lights up.
(Back of TV)
may be an infringement of copyright laws.
Hint
(Back of Recording VCR*)
(Back of Playing VCR)
Select an empty program
number
• To go back one step, press the REW button
(during the steps [3] to [9].)
ONE TIME PROGRAM
PROGRAM NUMBER
6
ANT
IN
2
4
AUDIO
OUIN
VIDEO
OUT
IN
AUDIO
1
DATE
0 5 / 0 3 MON
OUT
IN
VIDEO
Connect
START TIME 0 7 : 3 0 PM
END TIME – – : – – – –
OUT
To Check, Correct, or Cancel a
Timer Program
Connect
or
CHANNEL
– –
REC SPEED – –
3
4
AM
PROGRAM NUMBER
4
RF Cable
(supplied)
1) Turn the power on by pressing
B PM
B ONCE
DAILY
WEEKLY
the POWER button.
Audio/Video Cables
(not supplied)
Select “AM” or “PM”
*Front input jacks are also available
2) Select main menu by pressing
the MENU button.
or
1) Insert a pre-recorded tape into the playing VCR.
2) Insert a tape with its record tab into the recording VCR.
3) Select "TIMER PROGRAM-
MING" by pressing the PLAY or
STOP button. Then, press the
F.FWD button.
3) Press the SPEED button on the remote control of the recording VCR
7
8
Repeat the procedure in steps
5 and 6 to set the end time.
Select “ONCE”, “DAILY”
(Mon-Fri), or “WEEKLY”
to select the desired recording speed (SP/SLP).
4) Select the program number
which you want to check by
pressing the PLAY or STOP but-
ton. The details of the program
you selected will appear on the
TV screen.
• Go to the digit you want to
change by pressing the F.FWD
or REW button. Then, enter cor-
rect numbers by pressing the
PLAY or STOP button.
• You may cancel the entire pro-
gram by pressing the REW but-
ton while the program number
flashes.
5) Press the C.RESET/EXIT button
to exit.
6) Press the POWER button to
return to timer stand-by mode.
4) Select the “L1” or “L2”position on the recording VCR.
• To use the input jacks on the back of the VCR, select "L1" position by
pressing [0], [0], [1] on the remote control or the CHANNEL buttons.
• To use the input jacks on the front of the VCR, select "L2" position by
pressing [0], [0], [2] on the remote control or the CHANNEL buttons.
ONE TIME PROGRAM
Select the desired month
PROGRAM NUMBER
DATE 0 5 / 0 3 MON
START TIME 0 7 : 3 0 PM
END TIME 0 8 : 3 0 PM
4
ONE TIME PROGRAM
PROGRAM NUMBER
4
5) Press the REC/OTR button on the recording VCR.
6) Begin playback of the tape in the playing VCR.
or
DATE 0 5 / 0 3 MON
START TIME – – : – – – –
END TIME – – : – – – –
or
CHANNEL
1 6
REC SPEED – –
7) To stop recording, press the STOP/EJECT button on the recording
CHANNEL
– –
REC SPEED – –
VCR, then stop playback of the tape in the playing VCR.
Select the desired channel
Hint
•
If you have connected the VCR to a cable
box or satellite box as the Connection A
on page 1, select the VCR to channel 3 or
4 (the RF output channel of the VCR).
Then, select the desired channel at the
cable box or satellite box. Leave the cable
box or satellite box on for timer recording.
Select the desired day
• For best results during dubbing, use the VCR’s front panel controls whenever possible. The
remote control might affect the playing VCR’s operation.
or
• Always use video-quality shielded cables with RCA-type connectors. Standard audio cables are
not recommended.
• You can use a video disc player, satellite receiver, or other audio/video component with A/V out-
puts in place of the playing VCR.
• “L1” or “L2” is found before the lowest memorized channel. (Example: CH02)
• You can program one
year in advance.
- 6 -
EN
10. Special Features
Time Search
Index Search
Auto Repeat
You can repeat playback of a
whole tape automatically.
You can specify the time for
fast forwarding or rewinding.
You can specify the number of
programs to be skipped.
• Insert a tape into the VCR.
• Insert a tape into the VCR.
• Insert a tape into the VCR.
1
MENU
-MENU-
1
INDEX SEARCH
SEARCH
1
TIME SEARCH
– –
-MODE
TIMER PROGRAMMING
B AUTO REPEAT [OFF]
CHANNEL SET UP
SEARCH
– : – –
-MODE
CLOCK SET
LANGUAGE SELECT
x1 (Once)
x2 (Twice)
or
2
INDEX SEARCH
0 3
2
Select the desired length
of time for fast forwarding
or rewinding
or
-MENU-
2
TIME SEARCH
2 : 5 0
TIMER PROGRAMMING
B AUTO REPEAT [ON]
CHANNEL SET UP
CLOCK SET
01 ~ 20
CURRENT PROGRAM
Beginning
End
LANGUAGE SELECT
or
of tape
of tape
Pro.1 Pro.2 Pro.3 Pro.4 Pro.5
02 01 01 02 03
INDEX MARK
0:01~ 9:59
(1 minute~9 hours
and 59 minutes)
3
AUTO REPEAT B
To rewind
To fast forward
3
4
To rewind
To fast forward
After searching,
3
4
Hint
• To cancel Auto Repeat, follow steps [1]-[2]
above. Then, press the F.FWD button so
that [OFF] appears beside AUTO REPEAT.
Press the C.RESET/EXIT button to exit.
After searching,
• If menu remains on the TV screen at step
[3], press the C.RESET/EXIT button to exit.
PLAYB
PLAYB
Hint
• The VCR records an index mark at the
beginning of the recording when you make
a recording. There should be time gap
between index marks for the Index Search.
Hint for Timer Search & Index Search
• These functions are not available during recording.
• Press the STOP button to stop the search.
• If the end of the tape is reached during a Search, the VCR will cancel the search and rewind the
tape.
- 7 -
EN
11. Information
Limited Warranty
Maintenance
Funai Corporation will exchange or repair this product, at THIS WARRANTY DOES NOT COVER PACKING
its option, in the event of defect in materials or workman- MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
Servicing
Auto Head Cleaning
ship as follows:
CONTROL UNITS), ANY COSMETIC PARTS, COM-
PLETE ASSEMBLY PARTS, DEMONSTRATION OR
FLOOR MODELS.
Should your VCR become inoperative, do not • Automatically cleans video heads as you insert or
try to correct the problem by yourself. There remove a cassette, so you can see a clear picture.
are no user-serviceable parts inside. Turn off, • Playback picture may become blurred or interrupt-
EXCHANGE DURATION:
1-90 DAYS:
FUNAI CORPORATION will exchange
FUNAI CORPORATION AND ITS REPRESENTATIVES
OR AGENTS SHALL IN NO EVENT BE LIABLE FOR
ANY GENERAL, INDIRECT OR CONSEQUENTIAL
DAMAGES ARISING OUT OF OR OCCASIONED BY
THE USE OF OR THE INABILITY TO USE THIS PROD-
UCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES INCLUDING THE WARRANTY
OF MERCHANT ABILITY, AND FITNESS FOR A PAR-
TICULAR PURPOSE, THAT ARE HEREBY DIS-
CLAIMED BY FUNAI CORPORATION AND ITS REP-
RESENTATIVES OR AGENTS IN THE UNITED
STATES.
for a new unit without charge for a peri-
od of ninety (90) days from the date of
original retail purchase.
unplug the power plug, and please call our
help line mentioned on page 1 to locate an
Authorized Service Center.
ed while the TV program reception is clear. Dirt
accumulated on the video heads after long peri-
ods of use, or the usage of rental or worn tapes
can cause this problem. If a streaky or snowy pic-
ture appears during playback, the video heads in
your VCR may need to be cleaned.
91-365 DAYS: FUNAI CORPORATION will exchange
for a factory-service-to-new-condition
Cabinet Cleaning
unit for a charge of a retailed price unit
for the period of ninety one (91) days to
three hundred sixty five (365) days from
the date of original retail purchase.
• Wipe the front panel and other exterior sur-
faces of the VCR with a soft cloth immersed
in lukewarm water and wrung dry.
• Never use a solvent or alcohol. Do not spray
insecticide liquid near the VCR. Such chemi-
cals may cause damage and discoloration to
the exposed surfaces.
1. Please visit your local Audio/Video store and pur-
chase a good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the
problem, please call our help line mentioned on
page 1 to locate an Authorized Service Center.
NOTES:
REPAIR DURATION:
LABOR:
FUNAI CORPORATION will provide the
labor without charge for a period of
ninety (90) days from the date of origi-
nal retail purchase.
FUNAI CORPORATION will provide
parts to replace defective parts without
charge for a period of one (1) year from
the date of original retail purchase.
Certain parts are excluded from this
warranty.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST
BE PERFORMED BY A FUNAI AUTHORIZED CEN-
TER. THIS WARRANTY IS VALID WHEN THE PROD-
UCT IS DELIVERED PREPAID TO A FUNAI AUTHO-
RIZED SERVICE FACILITY.
• Remember to read the instructions included with
the video head cleaner before use.
PARTS:
• Clean video heads only when problems occur.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE, IF AT ANY TIME
DURING THE WARRANTY PERIOD YOU ARE UNABLE
TO OBTAIN SATISFACTION WITH THE EXCHANGE
OR REPAIR OF THIS PRODUCT, PLEASE CONTACT
FUNAI CORPORATION.
Instrucciones en Español
PREPARACIÓN DEL RELOJ
LIMITS AND EXCLUSIONS:
PREPARACIÓN DE CANALES
(La antena o la caja de televisión por
cable deberá estar conectada)
NOTES: Cuando utilice su nueva
videograbadora por primera vez, o en el
caso de ser necesario después de pro-
ducirse un fallo en la alimentación, la
videograbadora se pondrá inicialmente en el
modo de preajuste cuando se pulse
[POWER].
1. Encienda el televisor y ponga el televisor
en el canal 3.
2. Pulse [POWER] para encender la
videograbadora.
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGI-
NAL RETAIL PURCHASER. A PURCHASE RECEIPT
OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE
WILL BE REQUIRED TOGETHER WITH THE PROD-
UCT TO OBTAIN EXCHANGE OR SERVICE UNDER
THIS WARRANTY.
1. Pulse [MENU] hasta que aparezca el
menú principal. (Si el reloj no está puesto
en hora y se pulsa [MENU], el menú
AJUSTE DE RELOJ aparece en primer
ATTENTION:
FUNAI CORPORATION RESERVES THE
RIGHT TO MODIFY ANY DESIGN OF THIS
PRODUCT WITHOUT PRIOR NOTICE.
For information about your product, or for
information on how to exchange or repair your
product, telephone or write to the following:
This warranty shall not be extended to any other person
or transferee.
lugar. En este caso, siga el paso 3.)
2. Pulse [PLAY] o [STOP] para indicar a
"AJUSTE DE RELOJ". Luego, pulse [F.FWD].
3.
This warranty is void and of no effect if any serial num-
bers on the product are altered, replaced, defaced or
missing. This SYLVANIA Limited warranty applies only to
product purchased and used in the United States.
This product is produced for home use and this warranty
only covers failures due to defects in material or work-
manship, which occur during normal use. It does not
cover damage which occurs in shipment, or failures
which are caused by repairs, alterations, or parts not
supplied by FUNAI CORPORATION, or damage which
results from accident, misuse, abuse, mishandling, mis-
application, alteration, faulty installation, improper main-
tenance, commercial use such as hotel, rental or office
use of this product, or damage which results from fire,
flood, lightning or other acts of God.
Pulse repetidamente [PLAY] o [STOP].
Luego, pulse [F.FWD].
Ajuste el mes.
Ajuste el día.
Pulse repetidamente [PLAY] o [STOP].
Luego, pulse [F.FWD].
FUNAI CORPORATION, INC.
SERVICE CENTER
Pulse repetidamente [PLAY] o [STOP].
Luego, pulse [F.FWD].
Ajuste el año.
Ajuste la hora.
19900 Van Ness Avenue, Torrance, CA 90501
Tel :1-800-968-3429
3. Seleccione "ENGLISH",
"FRANCAIS"(French)
Pulse repetidamente [PLAY] o [STOP].
Luego, pulse [F.FWD].
o "ESPAÑOL"
(Spanish) pulsando
[PLAY] o [STOP]. Y
luego pulse [F.FWD].
4. Pulse una vez
[F.FWD].
SELEC. IDIOMA
Ajuste el minuto. Pulse repetidamente [PLAY] o [STOP].
Luego, pulse [F.FWD].
Head Office: 100 North Street, Teterboro, NJ 07608
PLEASE DO NOT SHIP YOUR UNIT TO THE
TETERBORO ADDRESS.
ENGLISH
FRANCAIS
Ajuste la
mañana (AM) o
Pulse repetidamente [PLAY] o [STOP].
B ESPAÑOL
[ON]
la tarde (PM).
AJUSTE DE RELOJ
MES
03
DIA
AÑO
2004
/
15 LUN
• Para volver atrás un
paso, pulse [REW].
4. Pulse [F.FWD] para
poner en fun-
El sintonizador explora
HORA MINUTO AM/PM
05
y memoriza todos los canales activos de su
zona. Tras la exploración, el sintonizador se
detiene en el canal memorizado más bajo.
:
40
PM AM
BPM
cionamiento el reloj.
- 8 -
EN
|