Color profile: Generic CMYK printer profile
Composite Default screen
Dig it al cord less h an d set for
use w it h t h e Fusion 2510
b ase t elep h on e an d
Fu sio n 2 5 1 0
Customising your phone, continued
Con t en t s of t h is User Guid e
9 Reset t in g t h e syst em
Your securit y PIN
1
2
3
4
5
6
7
8
W h ere t o fin d it
If you reset the system, you will lose all stored information (including
numbers in memory) and all features will return to their default settings.
an sw erin g m ach in e
!
!
You will only need this feature if you plan to set up Call Barring.
Makin g an d an sw erin g calls
Ph on e Book (m em ory d iallin g )
Caller Disp lay
While you are resetting the system, you should disconnect the telephone
line cord from the back of the base unit, so you won’t be interrupted by
incoming calls.
The base unit has a default PIN (personal identity number) of 0000. You can
change it to any number you’ll remember, with up to eight digits.
USER GUIDE
à
à
1
2
3
4
5
6
Press MENU
Press OK
then
■
TWICE
phonebk
base
There are two methods of resetting the system. You’ll only need the second one
if you have set a PIN and forgotten it. The PIN will be reset to 0000.
Ton es an d volum es
Call b arrin g
If you n eed h elp …
The Binatone Help Line is available from
9.00 am to 5.00 pm, Monday to Friday,
on
à
Press
■
SIX times
pin code
Reset w it h t h e PIN
à
Cust om isin g your p h on e
Reset t in g t h e syst em
Press OK
pin
à
à
1
2
3
4
5
6
Press MENU
Press OK
then
■
TWICE
phonebk
base
à
Key in the existing PIN (default 0000) and press OK
new pin
1300 768 112
Calls are charged at Local Call rate.
à
volume
à
Key in the your new PIN and press OK
retype
10 In t ercom , t ran sfer an d con feren ce
11 Han d set reg ist rat ion
12 Op erat ion al n ot es
à
Press
■
NINE times
default
Key in the your new PIN again and press OK
Or visit our website:
h t t p :/ / w w w.b in at on et elecom .com /
à
9
Press MENU
to go back to standby mode
Press OK
pin
If you forget your new PIN, you’ll need to reset the system, and you’ll
lose any numbers you’ve stored in memory.
Key in your PIN (default 0000)
13 Troub lesh oot in g
!
Press OK
à You hear a confirmation tone from the handset and
base unit.
For installation instructions, guarantee and service information and
a technical specification, refer to the user guide for the base unit
telephone.
Reset w it h out t h e PIN
1
Remove the batteries from the handset
For instructions on how to operate the an sw erin g m ach in e, refer
to the user guide for the base unit telephone.
2
à
Press and hold STAR
while you replace the batteries
default
3
Release STAR
and press OK
Pressin g b ut t on s on your p h on e
à You hear a confirmation tone from the handset and base unit, and
search 1 will appear on the display for a few moments.
When the instructions in this user guide tell you simply to
‘p ress’ a button, this means that you should press the
button briefly, then release it.
When the instructions tell you to ‘p ress an d h old ’
a button, this means you should keep the button pressed
until the display changes and/or you hear a tone.
Im p ort an t n ot e — em erg en cy calls
The Fusion 2510 cordless handset is not designed for making
emergency calls when the mains power fails. If you need to call
Emergency Services. During a power failure, use the base unit
telephone (you’ll need to lift the handset, not use the speakerphone).
Australia Ver 1, Apr 06
1
15
16
14
To d e-reg ist er a h an d set
11 Han d set reg ist rat ion
To t ran sfer a call
When you’ve made or answered an outside call, to transfer it to another handset:
You may need to do this if you need to replace a faulty handset. Call the
Binatone Help Line if you need more advice.
10 In t ercom , t ran sfer & con feren ce
The handset(s) supplied with your Fusion 2510 base unit are already
registered — the first one as handset number 1, the second as number 2.
You don’t need to re-register them unless you have a problem.
To check whether a handset is registered, make sure mains power to the base
unit is switched on and the handset is within range. The handset’s display
should show its number, and the ‘signal level’ symbol on the display should
show three bars. If the display shows not sub , you need to re-register the
handset.
à
1
2
3
4
5
6
7
Press MENU
Press
Press OK
Press
Press OK
phonebk
à
If you have a Fusion 2510 Twin, Triple or Quad system, you already have two,
three or four handsets.
Altogether, you can have up to five handsets registered to the base unit, as
numbers 2, 3, 4 and 5.
1
Press INTERCOM
and key in the number of the other handset
!
■
TWICE
base
à The outside call is put on hold. When the other handset answers, you can
speak to the user. If the other handset does not answer, you can get back to
the outside call by pressing INTERCOM again.
à
volume
à
■
SEVEN times
del hs
With more than one handset registered to your base unit, you can
To transfer the outside call to the other handset:
à
pin
■
■
■
■
■
make intercom calls from one handset to another
make a new intercom call while you are on an outside call
shuttle between an outside call and an intercom call
transfer an outside call from one handset to another
set up a three-way conference call between yourself, an outside call and an
intercom call
2
Press PHONE
to hang up and transfer the call
Key in your PIN (default 0000) and press OK
To sh ut t le b et w een t w o calls
Press
■
repeatedly to go to the number of the handset
you want to de-register
To reg ist er a n ew h an d set or t o re-reg ist er a h an d set
When you have both an outside call and an intercom call connected, you can
shuttle from one to the other, like this:
1
Press HANDSET LOCATOR
on the base unit for about 3 seconds
à
8
9
Press OK
Press OK
confirm
Press INTERCOM
other on hold
to speak to each call in turn, putting the
■
à You hear two short beeps and the IN USE light flashes. You now have
3 minutes in which to register the handset.
to confirm de-registration
Each handset has its own number — 1, 2, 3, 4 or 5 — which is shown on the
right-hand side of the display.
Note — you cannot de-register the handset you are currently using.
You can transfer the outside call to the other handset by pressing PHONE
while you’re connected on the intercom call
à
2
Press MENU
on the handset
register
Note: the main base unit does not have intercom facility.
(If the display does not show register at this point, press
■
until it does.)
If you press PHONE while you’re connected to the outside call, you will
disconnect it.
If the other handset user presses PHONE on their handset to hang up, you’ll
be left connected to the outside call.
Reg ist erin g t o a d ifferen t b ran d of b ase un it
Please n ot e —
à
3
4
Press OK
Key in 1
BS 1 2 3 4
(These are base unit numbers.)
Your Fusion 2510 handsets can be registered to any GAP-compatible base unit;
or you can register other GAP-compatible handsets to your Fusion 2510 base
unit. But we do not guarantee that all features or display messages will be
available using other manufacturers’ equipment.
■
■
■
■
Among the handsets registered to a single base unit, only one outside call
and two intercom calls can take place at once.
à
(base unit number 1)
pin
If you try to make an outside call while another handset is already on the line,
you will hear Busy tone.
(Or, if the handset is already registered to a different base unit, key in a base
unit number that is not flashing.)
Con feren ce calls
1
Follow the instructions in the base unit’s User Guide to put the base unit into
To set up a three-way conference between yourself, an outside call and an
intercom call with another handset:
If you try to make an intercom call when one is already in progress, you will
hear Busy tone.
à
5
6
Key in your PIN (default 0000) and press OK
search
registration mode (for example, step 1 of the registration procedure listed
here).
à After a few moments, when the handset finds the base unit, a number*
appears on the display.
When one handset is using the outside line, the EXT symbol will appear on
1
2
Either make or answer an outside call
2
Follow the instructions in the handset’s User Guide to register the handset
(for example, steps 2 to 5 listed here). If you need to enter a PIN code for the
base unit, refer to the base unit’s User Guide.
the displays of all other handsets.
Press INTERCOM
then key in the number of the other handset
Press OK
to confirm registration
The other user answers by pressing PHONE on their handset.
To m ake an in t ercom call
The handset’s display should now show its name and number.
3
Press # (HASH)
and hold it for about 2 seconds
To make a call to another handset
If you have problems, contact the Binatone Help Line for more advice.
If the display still says not sub , go through the registration procedure
again from step 1. If registration doesn’t work this time, call the Binatone
Help Line for advice.
à You hear a confirmation tone when your conference call is connected. If
either handset user presses PHONE to hang up, the other user will be left
connected to the outside call.
1
2
Press INTERCOM
à You hear Dial tone
Key in the number of the other handset (1, 2, 3, 4 or 5)
à The other handset’s number appears on your display. On its display, your
number appears, and the INT symbol flashes. When the other handset user
presses the PHONE button to answer, you will be connected.
*This is the RFPI number, a universal DECT identity number. You won’t need it unless
you want to register your handset to a different brand of DECT base unit.
Waste electrical products must not be disposed of with
household waste. This equipment should be taken to
your local recycling centre for safe treatment.
New Call t on e
When you are on an intercom call and an outside call comes in, you will hear
New Call tone over your conversation to tell you that someone is calling you.
The EXT symbol will also flash on your handset’s display.
To en d an in t ercom call
Press PHONE
on your handset
■
1
2
Press PHONE
Press PHONE
to end the intercom call à Your handset will ring
à The other person will hear Busy tone, and should also press PHONE to
hang up.
again to answer the outside call
16
17
18
19
In t ercom an d t ran sfer
“The cordless
phone does
not ring”
Check that the base unit’s mains power adapter is plugged in
and power is switched on. The cordless phone won’t work if the
base unit has no electrical power.
12 Op erat ion al n ot es
13 Troub lesh oot in g
“I can’t transfer a
call.”
Make sure the other cordless handset is within range of the base
unit, and is not busy on a call.
In t erferen ce
The Fusion 2510 must be serviced by trained engineers. NEVER attempt
any repairs or adjustments yourself — you could make the problem
worse and invalidate the Guarantee.
Check that you have not set the ringer volume to Off. See
Section 6 for more information.
Make sure you are keying in the correct number (1 to 5) for the
other handset.
!
If the sound quality gets worse as you move around while on a call, this is
probably due to interference between the handset and the base unit, perhaps
because you are too near to another phone or other electrical equipment. Move
to a different position to clear the interference. If you do not move, your call
may be cut off.
“My call was cut
off when I went
out of range.
Now I can’t use
my handset.”
Move the cordless handset closer to the base unit before you try
again to make a call.
Bat t eries
ALWAYS check
first that:
■
you have followed the steps listed in the main user guide to
install and set up your Fusion 2510
“The handset‘s
batteries are
running low
within an hour or
two.”
“The CHARGE
light on the
charger pod does
not come on.“
Before you first used the handset, you should have left it on the
charger pod for up to 15 hours to charge the batteries fully.
■
■
■
all connectors are firmly inserted in their sockets
mains power is switched on at the socket
Radio interference in the environment may occasionally cause a short break in
the link between the handset and the base unit while you are on a call. The
handset’s display will flash briefly, while the unit automatically changes to a
different channel to restore the link.
You may need to replace the batteries
the cordless handset’s batteries are correctly and securely
installed, and are not run down
“There is inter-
ference, noise or
echoing on the
line.”
Move the cordless handset closer to the base unit, or to a
different position.
Clean the battery charging contacts with a dry cloth.
Try moving the base unit so that it’s not near other electrical
equipment, such as a TV or a computer.
Check the connections between the charger pod and the mains
power socket.26
Everyd ay use
Keep in g t h e b at t eries ch arg ed
When you don’t need to carry your handsets around (for example, at night),
leave them on the charger pod, to keep the batteries charged.
“I cannot make or Check that the base unit’s mains power adapter is plugged in
You’ll get the best results if you site the base unit as high as
possible. For example, in a two-storey house, the first-floor
landing is an ideal place for the base unit.
answer calls.”
and power is switched on. The cordless phone won’t work if the
base unit has no electrical power.
“I try to recharge
You need to replace the batteries. Please note the following
the batteries, but safety warnings:
Whenever the battery charge level symbol on the display shows ‘nearly empty’,
replace the handset on the charger pod.
I still get a
warning that they
are low.”
Move the handset closer to the base unit.
■
Use only NiMH (Nickel metal hydride) 1.2 V AAA
“When I press the The strange noise is caused by interference. Disconnect the mains
PHONE or
SPEAKERPHONE
button, I hear a
loud noise.”
rechargeable batteries in the handset. The best way to make
sure you get the right batteries is to take the old ones with you
when you go to buy new ones.
Check the Battery Level symbol on the display. If it is low,
replace the cordless handset on the charger pod to recharge the
batteries.
power lead from the back of the base unit, then wait 30 seconds
before reconnecting it.
‘Out of ran g e’ w arn in g
■
Dispose of used batteries safely — never burn them, or put
If you hear a warning tone during a call, and/or the sound in the earpiece
becomes faint or distorted, you may be going out of range of the base unit.
Move nearer to the base unit within 20 seconds, until the tone stops.
Otherwise, your call may be cut off.
If you still can’t make calls, try re-registering the handset.
them where they could get punctured.
“I hear ‘beeps’
from my handset your call may be cut off.
while I’m on a
call.”
You may be going out of range of the base unit. Move closer, or
“When I press
keys on the
Make sure the batteries are fitted in your handset. If the Battery
Level symbol on the display shows ‘low’, recharge the batteries.
PBX use
While you are out of range and you are not on a call, the handset’s display
shows search and the ‘signal level’ symbol flashes. Before you make a call,
you must move closer to the base unit until the handset’s name and number
are displayed and the symbol stops flashing.
“Last Number
Redial and/ or
memory dialling
don’t work on a
PBX.
When you first make a call, try pressing the CDS button for a
pause between the outside line access digit (e.g. 9) and the tele-
phone number. You should later be able to redial the number.
handset, nothing
happens.”
Check the Battery Level symbol on the display. If it shows ‘low’,
recharge the batteries.
Press and hold the OK button until the handset comes to life. The
OK button switches the handset on and off.
Check whether there’s a ‘key’ symbol on the display. If so, the
keypad is locked. Turn to Section 8 to find out how to unlock it.
“The volume in
the earpiece is
low.”
Make sure you’re holding the earpiece correctly over your ear.
Adjust the volume as decribed in Section 6.
When storing numbers in memory, you can include the outside
line access digit (e.g. 9) with each number.
If your PBX requires you to wait for a second Dial tone before
dialling the telephone number, press the CDS button for a pause
between the access digit and the number.
“When I press
keys on the
Call barring may have been set. See Section 7 for more
information.
“When I try to
Check your handset’s display — if it says either notsub or
make a call, I hear base.... , you need to re-register the handset.
Busy tone and
the IN USE light
on the base unit
does not come
on.”
handset, digits
appear on the
display, but I
can’t make an
outside call.”
Try moving the handset closer to the base unit.
If the display says search1 , make sure the mains power lead
is plugged into the back of the base unit, and the adapter is
plugged into the mains socket with the power switched on.
“My Fusion 2510
cordless handset
won’t work
properly on a
PBX.“
You may need to change the recall setting. Call the Binatone
Help Line for advice. It will help if you have your PBX
documentation to hand when you make the call.
Try a different position for the base unit — perhaps higher, or
further from other electrical equipment.
If you have more than one handset registered to your base unit,
check that another handset isn’t already in use on a call.
20
21
22
23
E:\Binatone2005\Fusion2510\Cordless_folding\Fusion2510_cordless_draft01a.vp
14 December 2005 12:27:06
|